Licensed, insured, and answering calls 24/7 across Newport Coast

Mold Cleanup Near Me in NEWPORT COAST, California

When you search for mold cleanup near me in NEWPORT COAST, California, you need a crew that finds the source, not just the stain. We handle black mold growth, musty odors, and water damage mold in homes and commercial buildings from Pelican Crest to Crystal Cove. Our mold cleaning service in NEWPORT COAST is built for coastal humidity, marine fog, and the plumbing leaks that hide behind walls. Call and we will be on-site the same day.

↗
Fast online booking

Request service today

Tell us what is happening. Our local team will confirm your visit shortly.

No spam. No obligation. Just practical help.
Thanks — we'll call shortly to confirm your visit.
Mold Cleanup Near Me by Mold Remediation Service Newport Coast
Careful work. Honest options.
About this service

What Mold Cleanup Near Me in NEWPORT COAST Really Involves

Mold cleanup near me in NEWPORT COAST, California is a containment-first remediation process that removes active mold growth, dries the source moisture, and verifies the air is clean before anyone moves back in. It is not a spray-and-wipe job. We set up polyethylene sheeting and zipper doors, run negative air machines with HEPA filters, and use a thermal imaging camera and moisture meter to find water you cannot see. Every job ends with air sampling, because a visual pass is not proof.

Coastal homes here sit in a marine layer that keeps relative humidity high most mornings, and that is enough to wake dormant spores after any slow leak. We see crawl space mold under Crystal Cove properties, attic mold from roof flashing failures, and bathroom ceiling mold in older condos along Newport Coast Drive. If you have been typing mold cleanup near me open now NEWPORT COAST into your phone at 11 p.m., call us. We answer around the clock and can start containment the same day.

  • ✓ Same-Day Containment
  • ✓ Source Found, Not Covered
  • ✓ Clearance Testing Included
  • ✓ Odor Gone, Not Masked
What's included

What Our Mold Cleanup Near Me Service Includes

Every remediation job includes the same core scope: inspection, containment, removal, drying, treatment, and clearance testing. What varies is how much material comes out and how long drying takes. We spell out what is included before we start, so you are never looking at an invoice and wondering where a line item came from.

✓

Full Moisture Inspection

Thermal imaging camera and moisture meter readings on every affected surface, plus a boroscope camera look inside wall cavities where we suspect hidden growth. You get photos and a written map of the affected area before any work starts.

✓

Containment Setup

Polyethylene sheeting, zipper doors, and negative air machines with HEPA filters isolate the work area. This keeps spores out of the rest of your Newport Coast home while removal is underway, including keeping them out of the HVAC system.

✓

Removal and HEPA Vacuuming

Porous materials with drywall mold or insulation growth go into sealed bags. Structural framing gets HEPA vacuumed with ProTeam and RIDGID units, then treated. We do not sand mold into the air; where wood is exposed, dry ice blasting is often the cleaner method.

✓

Drying and Dehumidification

Dri-Eaz and Phoenix Restoration dehumidifiers and air scrubbers run until moisture readings return to normal, typically 24 to 72 hours. We check readings daily and adjust equipment placement rather than letting it run blind.

✓

Antimicrobial Treatment

Concrobium or Benefect applied to framing and structural surfaces, with fogging for cavities that cannot be wiped. Crawl spaces get an encapsulation liner and vapor barrier where specified, which is the difference between a fix and a repeat call.

✓

Clearance Air Sampling

An air sampling pump collects indoor and outdoor samples after work is complete. You get the lab report. If spore counts do not return to normal, we re-clean at no additional charge before we pull containment.

How it works

What to Expect From Start to Clearance

01

Phone Assessment

We ask what you are seeing, smelling, and where. A 10-minute call usually tells us whether you need a full remediation or just an inspection. We give you a realistic range on the phone and book a same-day or next-morning visit. No dispatch fee for the estimate.

02

On-Site Inspection

Our IICRC AMRT-certified technician walks the property with a moisture meter and thermal imaging camera, and drops a boroscope camera into wall cavities where needed. We map the affected area, photograph everything, and identify the moisture source. This typically takes 45 to 90 minutes depending on square footage.

03

Containment and Removal

We seal the work area with polyethylene sheeting and zipper doors, set negative air machines with HEPA filters, and begin removal. Porous materials like drywall mold and insulation go into sealed bags. Structural framing gets HEPA vacuumed and treated with a biocide solution. A typical bathroom takes one day; a crawl space runs two to three.

04

Drying and Treatment

Dehumidifiers and air scrubbers run until moisture readings return to normal, usually 24 to 72 hours. We apply an antimicrobial coating to framing and, where specified, an encapsulation liner in crawl spaces. Concrobium fogging reaches surfaces you cannot wipe. We check readings daily and adjust equipment as needed.

05

Clearance Testing

An independent air sampling pump collects spore counts inside the contained area and outside for comparison. If levels do not pass, we re-clean at no additional charge. When they pass, we hand you the lab report, photos, and a written scope of what was removed and what was treated. That packet is what insurers and buyers want to see.

Tools & methods

Tools and Methods We Use on Every Job

Purpose-built equipment, used by trained technicians — so the job is done accurately the first time.

Thermal Imaging Camera

Finds temperature differentials behind walls and ceilings that indicate hidden moisture, without cutting exploratory holes. It is how we locate a leak source before demolition starts.

Moisture Meter

Quantifies moisture content in drywall, framing, and subfloor. We use readings to define the affected area and to decide when drying is actually complete rather than guessing.

Boroscope Camera

A small camera on a flexible probe that lets us look inside wall cavities and duct interiors without opening them up. It confirms or rules out hidden growth before we commit to a scope.

Negative Air Machine with HEPA Filters

Maintains negative pressure inside containment so air flows in, not out. Every unit runs HEPA filtration to capture spores at 0.3 microns before they reach the rest of the house.

HEPA Vacuum (ProTeam, RIDGID)

Removes settled spores from framing and surfaces without re-aerosolizing them. We use it on every structural surface before applying any liquid treatment.

Dehumidifier and Air Scrubber (Dri-Eaz, Phoenix Restoration)

Pulls moisture out of the structure and scrubs the air inside containment. Drying typically runs 24 to 72 hours depending on material and how long the water sat.

Dry Ice Blasting Machine

Strips mold from exposed framing and sheathing without sanding or chemical residue. It is our preferred method for structural wood in attics and crawl spaces where abrasive blasting would be too messy.

Real results

Before and after.

Crystal Cove Crawl Space Recovery

Before

A Crystal Cove homeowner noticed a musty smell in the living room that got worse after winter rains. Inspection found visible crawl space mold across roughly 600 square feet of joists and subfloor, with moisture readings well above normal and no vapor barrier in place.

After

We removed growth, HEPA vacuumed and treated the framing, ran dehumidifiers for 72 hours, and installed a 12-mil vapor barrier and encapsulation liner. Post-remediation air sampling came back at outdoor baseline levels, and the smell was gone within a day of clearance.

Pelican Hill Bathroom Ceiling Remediation

Before

Black mold growth covered about 30 square feet of bathroom ceiling drywall, spreading outward from the exhaust fan. The fan was venting into the attic rather than outside, so moisture had been accumulating for months. Framing above the drywall showed surface growth.

After

We removed the affected drywall under containment, HEPA vacuumed and treated the framing, corrected the vent run to terminate outside, and rebuilt with mold-resistant drywall. Clearance sampling passed on the first attempt, and the ceiling was repainted within a week.

Newport Ridge HVAC Contamination Fix

Before

A homeowner reported musty odors every time the AC kicked on, plus allergy symptoms that worsened indoors. Inspection with a boroscope camera found mold contamination on the air handler interior and in one flex duct run serving the primary bedroom.

After

We cleaned and treated the air handler under containment, replaced the affected duct run, and sampled air in three rooms plus outdoors. Indoor spore counts dropped to match outdoor baseline, and the odor complaint resolved within 24 hours of the system going back online.

Problems we solve

Mold Problems We Solve Across Newport Coast

Most mold calls trace back to one of a handful of causes. Here are the ones we see most often in Newport Coast, and what happens if they are left alone.

Ask a pro →
01

Musty smell that keeps coming back after cleaning

We trace the smell with a moisture meter and thermal imaging, find the colony, and remove it under containment. Fogging with Concrobium reaches cavities wiping cannot. Air sampling confirms the microbial compounds driving the odor are actually gone.

↗
02

Black mold growth on bathroom ceiling and grout

We remove affected drywall, HEPA vacuum and treat the framing, correct the ventilation problem that caused it, and re-test before closing up. A bathroom ceiling job typically runs one day plus drying time.

↗
03

Crawl space mold after winter rains

We remove growth, dry the space with dehumidifiers, treat framing, and install a vapor barrier and encapsulation liner. That combination addresses the moisture source rather than just the visible mold.

↗
04

Mold contamination in HVAC and ductwork

We inspect the air handler and duct interiors with a boroscope camera, then clean and treat under containment. NADCA-certified duct cleaning is available where the contamination extends into the distribution system.

↗
Proof you can check

Licensed, Certified, and Documented

✓
IICRC WRT (Water Damage Restoration Technician)Institute of Inspection, Cleaning and Restoration Certification
✓
IICRC AMRT (Applied Microbial Remediation Technician)Institute of Inspection, Cleaning and Restoration Certification
✓
IICRC ASD (Applied Structural Drying)Institute of Inspection, Cleaning and Restoration Certification
✓
ACAC CMI and CMR (Certified Mold Inspector and Remediator)American Council for Accredited Certification
✓
California CSLB License, EPA Lead-Safe Certification, OSHA 30Contractors State License Board, U.S. EPA, OSHA
Good questions

Frequently Asked Questions

(833) 929-5837 →

Most residential jobs run $450 to $3,500 in 2026, depending on square footage and whether structural materials are involved. A single bathroom ceiling with surface growth sits at the low end. A crawl space with full remediation, drying, and encapsulation runs $2,500 to $6,000. We give you a written range after the on-site inspection, before any work begins.

You already found us. We serve all of Newport Coast, from Pelican Crest and Pelican Hill to Crystal Cove, Pacific Ridge, and San Joaquin Hills. Call (833) 929-5837 and we will confirm a same-day or next-morning appointment. We are licensed, insured, and IICRC-certified, and we can send credentials before we arrive if you want to check.

For active water intrusion, we target 90 minutes or less from your call, 24 hours a day. For standard mold jobs without active water, we typically schedule same-day or next-morning. Response times run longer during heavy winter storms when multiple properties are calling at once, but we prioritize active leaks and standing water every time.

Yes. Every job includes HEPA vacuuming, treatment with a biocide solution or Concrobium, and an antimicrobial coating on structural framing. Crawl spaces get an encapsulation liner when specified. We finish with air sampling to confirm spore counts are back to normal. Sanitizing without clearance testing is only half the job, and we do not cut that corner.

Ready when you are

Need Mold Cleanup Near Me in NEWPORT COAST, California?

We answer the phone 24/7, we show up when we say we will, and we hand you lab results at the end. Licensed, insured, and IICRC-certified. Call (833) 929-5837 and we will book your inspection today.

Book an Inspection (833) 929-5837 →
Request an appointment

Contact Our Newport Coast Mold Team

Call (833) 929-5837 any time, day or night. We answer live, schedule inspections same-day when possible, and send a written scope before work starts. If you prefer email, send photos of the affected area to info@moldremediationservicenewportcoast.com and we will follow up with next steps.

Request received — our team will be in touch shortly.
Tap to call(833) 929-5837