Chemical-free mold removal that leaves framing dry and ready to rebuild

Dry Ice Blasting Mold in NEWPORT COAST, California

Dry ice blasting mold in NEWPORT COAST, California strips mold off framing, sheathing, and crawl space joists without water, sand, or chemical residue. If you have black mold growth behind drywall or in an attic after a roof leak, our dry ice mold removal in NEWPORT COAST gets the wood back to bare, clean lumber in a single visit. We contain the work zone, blast the growth off, and HEPA-vacuum the debris before we leave.

↗
Fast online booking

Request service today

Tell us what is happening. Our local team will confirm your visit shortly.

No spam. No obligation. Just practical help.
Thanks — we'll call shortly to confirm your visit.
Dry Ice Blasting Mold by Mold Remediation Service Newport Coast
Careful work. Honest options.
About this service

What Dry Ice Blasting Mold in NEWPORT COAST, California Actually Does

Dry ice blasting mold in NEWPORT COAST, California is a media-blasting method that fires rice-sized pellets of solid carbon dioxide at -109°F onto moldy surfaces at high velocity. The pellets sublimate on contact, so the mold, mildew, and surface grime lift off the wood without any liquid carrier. That matters in coastal homes where adding water to already-damp framing is the last thing you want. The process reaches into corners, nail heads, and the gaps between studs where a wire brush and a rag cannot follow.

We use it most often after a supply line failure, a roof leak, or a slow bathroom ceiling mold problem that soaked into the structure behind the drywall. In Pelican Crest and Crystal Cove, the marine layer keeps interior humidity high enough that attic mold and crawl space mold return fast if the source is not corrected. That is why we pair dry ice mold removal NEWPORT COAST with moisture mapping and a drying plan, not just a blast-and-go visit.

  • ✓ No Secondary Water Damage
  • ✓ Reaches Where Brushes Cannot
  • ✓ No Sand or Chemical Cleanup
  • ✓ Faster Turnaround for Rebuild
What's included

What Our Dry Ice Blasting Mold Service Includes

Every dry ice blasting mold in NEWPORT COAST, California job includes inspection, containment, blasting, HEPA vacuuming, antimicrobial application, and clearance testing. If your job needs a vapor barrier, new insulation, or drywall repair, we quote that as a separate line so you can see exactly what each phase costs.

✓

Moisture Mapping and Inspection

Thermal imaging camera and moisture meter readings on every affected surface, plus a boroscope check inside wall cavities. You get a written map of where the moisture is and how far it traveled.

✓

Full Containment Setup

Polyethylene sheeting, zipper doors, and a negative air machine with HEPA filters. Air scrubbers cycle the work zone 4 to 6 times per hour to keep spores out of the rest of the house.

✓

Dry Ice Blasting of Framing

Solid CO2 pellets at -109°F and 120 to 150 PSI strip mold off studs, joists, sheathing, and sills. The pellets sublimate on contact, so no water or sand is added to the structure.

✓

HEPA Vacuum and Antimicrobial

We vacuum the debris from every surface, then apply an antimicrobial coating such as Concrobium or Fiberlock to the cleaned framing to slow regrowth.

✓

Clearance Testing and Report

Air sampling pumps and lab analysis confirm the job is clean. You get the report and photo documentation for your insurance file, usually within 24 to 48 hours of the blast.

How it works

How Our Dry Ice Blasting Mold Process Works

01

Inspection and Mapping

We start with a thermal imaging camera and moisture meter walk-through to find every wet pocket, not just the visible mold. A boroscope camera checks inside wall cavities and behind baseboards. This step usually takes 60 to 90 minutes on a 2,000-square-foot home and tells us exactly which surfaces need blasting.

02

Containment Setup

We hang polyethylene sheeting with zipper doors and run a negative air machine with HEPA filters so spores stay in the work zone. Air scrubbers cycle the room air 4 to 6 times per hour. Setup takes about two hours and is required on every job where more than 10 square feet of mold is disturbed.

03

Dry Ice Blasting

Our technician suits up in personal protective equipment and runs the dry ice blasting machine at 120 to 150 PSI, depending on the wood species and how deep the growth sits. A two-person crew cleans roughly 150 to 250 square feet of framing per hour. The pellets sublimate on impact, so there is no slurry to contain.

04

HEPA Vacuum and Antimicrobial

Once the growth is off, we HEPA-vacuum the debris from sills, plates, and the floor, then apply an antimicrobial coating to the cleaned framing. We use products like Concrobium or Fiberlock, applied with a fogger or pump sprayer. This step adds about 90 minutes and leaves a surface that resists regrowth.

05

Clearance Testing

We run air sampling pumps and post-remediation mold testing before we call the job done. Clearance typically takes 24 to 48 hours for lab results. If spore counts are still elevated, we re-clean at no additional charge. You get the lab report and photo documentation for your insurance file.

Tools & methods

Tools and Methods We Use for Dry Ice Blasting Mold

Purpose-built equipment, used by trained technicians — so the job is done accurately the first time.

Dry Ice Blasting Machine

Fires solid CO2 pellets at -109°F and 120 to 150 PSI to strip mold off framing without water or sand.

Thermal Imaging Camera

Finds wet pockets behind drywall and in ceiling cavities before we open anything up.

Moisture Meter

Reads wood moisture content before and after blasting so we can prove the framing is drying.

Negative Air Machine with HEPA Filters

Keeps the work zone under negative pressure so spores stay contained during the blast.

Air Scrubber

Cycles the work zone air 4 to 6 times per hour through HEPA filtration to clear airborne spores.

Boroscope Camera

Checks inside wall cavities and behind baseboards without opening more drywall than necessary.

Air Sampling Pump

Collects spore samples for clearance testing before we call the job complete.

Real results

Before and after.

Attic Framing After a Roof Leak

Before

A Pelican Crest home had black mold growth across 300 square feet of attic sheathing and trusses after a roof leak sat for three weeks. Moisture readings were 26% on the sheathing, and two contractors recommended cutting out the deck.

After

We contained the attic, blasted the sheathing and trusses at 130 PSI, and HEPA-vacuumed the debris. Moisture readings dropped to 15% within 48 hours, and clearance testing passed on the first try. The roof deck stayed in place.

Crawl Space Joists in Crystal Cove

Before

A rental unit in Crystal Cove had crawl space mold across 500 square feet of joists and subfloor, with a musty odor traveling up through the floor. Moisture readings were 22% on the joists, and the vapor barrier was torn in three places.

After

Our crew blasted the joists and subfloor, HEPA-vacuumed the debris, and installed a new vapor barrier. Readings dropped to 14% in two days, and the tenant stopped complaining about the smell within a week.

Post-Fire Framing in Coastal Canyon

Before

A kitchen fire in Coastal Canyon was put out with water, and the structural lumber sat wet for two weeks before the rebuild started. Mold had started on the studs and sill plate, and the rebuild crew would not close the wall.

After

We blasted the charred and moldy framing, HEPA-vacuumed the debris, and applied an antimicrobial coating. Clearance testing passed, and the rebuild crew closed the wall three days later instead of cutting out the framing.

Problems we solve

Mold Problems Dry Ice Blasting Solves in NEWPORT COAST

Most of the calls we get are for mold that came back after a wet cleanup, or for framing that a general contractor wants to cut out. Dry ice blasting mold in NEWPORT COAST, California solves both by cleaning the wood without adding moisture and without tearing out structure that is still sound.

Ask a pro →
01

Mold keeps returning after a wet wipe-down

We blast the framing dry, HEPA-vacuum the debris, and apply an antimicrobial coating. Because no water is added, the wood dries instead of staying damp, which is why dry ice mold removal NEWPORT COAST jobs hold up where wet wiping failed.

↗
02

Contractor wants to cut out moldy framing

Dry ice blasting mold in NEWPORT COAST, California cleans the surface of the lumber without removing it. We test the wood after blasting and document the results, so your contractor can rebuild on the original framing with confidence.

↗
03

Attic mold after a roof leak

We contain the attic, blast the sheathing and trusses, and HEPA-vacuum the debris. Dry ice blasting for mold on framing NEWPORT COAST California is a good fit here because the attic stays dry and the roof deck does not have to come off.

↗
04

Crawl space mold and musty odors

Our dry ice blasting remediation NEWPORT COAST California crews blast the joists and subfloor, then set a vapor barrier and dehumidifier plan. Moisture readings typically drop below 16% within 48 hours of the blast.

↗
Proof you can check

Licensed, Certified, and Clearance-Tested

✓
IICRC WRT (Water Damage Restoration Technician)Institute of Inspection, Cleaning and Restoration Certification
✓
IICRC AMRT (Applied Microbial Remediation Technician)Institute of Inspection, Cleaning and Restoration Certification
✓
ACAC CMI (Certified Microbial Investigator)American Council for Accredited Certification
✓
ACAC CMR (Certified Microbial Remediator)American Council for Accredited Certification
✓
California CSLB Licensed ContractorCalifornia Contractors State License Board
Good questions

Frequently Asked Questions About Dry Ice Blasting Mold

(833) 929-5837 →

Most dry ice blasting mold jobs in NEWPORT COAST run $2,500 to $8,500 in 2026, depending on square footage, access, and whether containment is needed. A small attic with 200 square feet of framing sits near the low end; a full crawl space with 800 square feet of joists and a failed vapor barrier pushes toward the top. Clearance testing adds $300 to $600.

Yes. Dry ice blasting is safe for wood framing, electrical wiring, plumbing, and most building materials when a trained technician runs the equipment. The carbon dioxide pellets sublimate on contact and leave no chemical residue. Occupants stay out of the work zone during blasting, and we ventilate the space before anyone returns, usually within an hour of finishing.

The machine fires solid CO2 pellets at -109°F and 120 to 150 PSI at the moldy surface. The thermal shock freezes and lifts the mold, while the kinetic energy carries it off the wood. The pellets turn straight to gas, so the mold debris is the only thing left, and we capture that with a HEPA vacuum and air scrubber.

Yes, we set up containment on every job that disturbs more than 10 square feet of mold, which is the industry standard under IICRC guidance. That means polyethylene sheeting, zipper doors, and a negative air machine with HEPA filters. Containment keeps spores out of the rest of the house and protects your HVAC system during the blast.

Ready when you are

Schedule Dry Ice Blasting Mold in NEWPORT COAST, California

Call (833) 929-5837 for a same-day estimate on dry ice blasting mold in NEWPORT COAST, California. We bring the moisture meter and thermal camera to the first visit, and you get a written scope before any work starts. Licensed, insured, and clearance-tested on every job.

Get a Free Estimate (833) 929-5837 →
Request an appointment

Contact Our Newport Coast Mold Team

Call (833) 929-5837 any time, day or night. We answer live, schedule inspections same-day when possible, and send a written scope before work starts. If you prefer email, send photos of the affected area to info@moldremediationservicenewportcoast.com and we will follow up with next steps.

Request received — our team will be in touch shortly.
Tap to call(833) 929-5837